@article { author = {Soheilpour, Zahra and Rezadoust, Amir Masood and Razavi-Nouri, Mohammad and Garoosi, Keyvan and Ghaffarian, Seyed Reza}, title = {Influence of Multi-Walled Carbon Nanotubes on Tensile Properties and Printing Quality of 3D-Printed Acrylonitrile-Butadiene-Styrene Nanocomposites}, journal = {Iranian Journal of Polymer Science and Technology}, volume = {32}, number = {6}, pages = {497-507}, year = {2020}, publisher = {}, issn = {10163255}, eissn = {20080883}, doi = {10.22063/jipst.2020.1705}, abstract = {Hypothesis: Due to the nature of a fused deposition modeling (FDM), by which the parts are fabricated layer by layer, many defects are  prone to occur  during printing of the products. Therefore, a few efficient solutions are required to minimize the defects and other shortcomings. The increase in the physical and mechanical properties of the fabricated parts using nanoparticles seems to be one of the methods. Methods: To improve the mechanical properties of acrylonitrile-butadiene-styrene (ABS), which is one of the most common materials employed in FDM technique, various amounts (1, 3 and 5 wt%) of multi-walled carbon nanotubes (MWCNTs) were added to the matrix through a melt mixing process. The filaments containing different MWCNTs contents, required for fabricating of the samples, were then prepared by extrusion. Next, the samples were printed with the layer thicknesses of 0.05, 0.1 and 0.2 mm and raster angles of +45/-45° and 0/90°. Several experiments such as the tensile and rheological tests as well as scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations were carried out to examine the nanocomposite samples.Finding: The SEM and TEM studies revealed that the nanoparticles were reasonably well dispersed throughout the matrix. The results of the tensile tests indicated that by addition of MWCNTs, the tensile strength and Young's modulus were increased by 21% and 103%, respectively, in comparison to those of the pristine material. It was also found that at a constant layer thickness, the maximum value of the tensile strength was obtained for the nanocomposite containing 3 wt% MWCNTs, however, the modulus progressively increased with the increase of the nanoparticles content. In addition, the change in raster angle showed no significant effect on the tensile properties, and the increasing of the layer thickness had an adverse effect on the properties for all the materials examined.}, keywords = {3D printing,fused deposition modeling,Nanocomposite,acrylonitrile-butadiene-styrene,mechanical properties}, title_fa = {اثر نانو‌لوله‌های کربن چنددیواره بر خواص کششی و کیفیت چاپ نانوکامپوزیت‌های آکریلونیتریل-بوتادی‌ان-استیرن چاپ‌شده سه‌بعدی}, abstract_fa = {فرضیه: به‌دلیل ماهیت مدل‌سازی لایه‌نشانی همجوش (FDM) که در آن قطعه‌ها به‌شکل لایه‌لایه ساخته می‌شوند، محصولات حین فرایند چاپ مستعد نقص‌های بسیاری هستند. بنابراین، برای به‌حداقل‌رساندن نقص‌ها و سایر کاستی‌ها به راه‌حل‌های کارآمدی نیاز است. افزایش خواص فیزیکی و مکانیکی قطعه‌های ساخته‌شده با استفاده از نانوذرات یکی از این روش‌هاست.روش‌ها: به‌منظور بهبود خواص مکانیکی آکریلونیتریل-بوتادی‌ان-استیرن (ABS) که یکی از مرسوم‌ترین مواد به‌کار گرفته‌شده در روش FDM است، مقدارهای مختلف (1، 3 و %5 وزنی) نانولوله‌های کربن چنددیواره (MWCNTs) با روش اختلاط مذاب به ماترس پلیمر افزوده شد. سپس، رشته‌های دارای مقادیر مختلف MWCNTs لازم برای ساخت نمونه‌ها، با روش اکستروژن تهیه شدند. پس از آن، نمونه‌ها با سه ضخامت لایه مختلف 05/0، 1/0 و mm 2/0 و دو زاویه رشته‌نشانی 90/0 و °45-/45+ چاپ شدند. آزمون‌های مختلف کشش، رئولوژی، میکروسکوپی الکترونی پویشی (SEM) و عبوری (TEM) برای بررسی‌ نمونه‌های نانوکامپوزیتی انجام شد. یافته‌ها: مطالعات SEM و TEM نشان داد، نانوذرات به‌شکل مناسبی درون ماتریس پراکنده شدند. نتایج آزمون کشش نشان داد، استحکام کششی و مدول یانگ در اثر افزودن MWCNTs به‌ترتیب تا 21 و %103 در مقایسه با ماده اولیه افزایش یافته است. همچنین مشخص شد، در ضخامت لایه ثابت، بیشینه استحکام کششی برای نانوکامپوزیت دارای %3 وزنی MWCNTs به‌دست آمد، اما با افزایش مقدار نانوذرات، مدول به‌تدریج افزایش یافت. افزون بر این، تغییر در زاویه رشته‌نشانی اثر معنی‌داری بر خواص کششی نشان نداد و نیز افزایش ضخامت لایه اثر منفی بر خواص تمام مواد بررسی‌شده داشت.}, keywords_fa = {چاپ سه‌بعدی,مدل‌سازی لایه‌نشانی هم‌جوش,نانوکامپوزیت,آکریلونیتریل-بوتادی‌ان-استیرن,خواص مکانیکی}, url = {http://jips.ippi.ac.ir/article_1705.html}, eprint = {http://jips.ippi.ac.ir/article_1705_c22dc5e2024b3a33e12aaa1ebb4041f2.pdf} }