اثر بار خمشی بر رسانندگی الکتریکی کامپوزیت‌های کربن-اپوکسی پرشده با نانوذرات

نوع مقاله : پژوهشی

نویسندگان

1 تهران، پژوهشکده توسعه تکنولوژی جهاد دانشگاهی صنعتی شریف، صندوق پستی 686-13445

2 تهران، دانشگاه علم و فرهنگ، دانشکده مهندسی مکانیک، صندوق پستی 68151-14619

3 تهران، دانشگاه علم و صنعت، دانشکده مهندسی مکانیک، صندوق پستی 13114-16846

4 تهران، دانشگاه تربیت مدرس، دانشکده مهندسی مکانیک، صندوق پستی 146-14115

چکیده

فرضیه: هدف از این پژوهش بررسی اثر بار خمشی بر رسانندگی الکتریکی کامپوزیت‌های کربن-اپوکسی دارای انواع نانوذرات مختلف بود. نمونه‌های توسعه‌یافته باید ضمن داشتن استحکام خمشی کافی، رسانندگی الکتریکی پیشنهادشده در استاندارد مؤسسه انرژی آمریکا را داشته باشند تا در ساخت الکترودها استفاده شوند.
روش‌ها: بدین منظور، از نانو‌ذرات دوده، نانولوله‌های کربن و گرافیت انبساط‌‌یافته همراه با الیاف کربن و رزین اپوکسی برای ساخت نمونه‌ها استفاده شد. ذرات دوده، نانولوله کربن و گرافیت انبساط‌‌یافته با مقادیر وزنی بهینه (25، 10 و %15) به کامپوزیت کربن-اپوکسی اضافه شده و آستانه رسانندگی الکتریکی نمونه‌ها مطابق روش استحکام چهارنقطه‌ای اندازه‌گیری شد. متوسط آستانه تراوایی رسانندگی الکتریکی برای کامپوزیت‌های دارای دوده، گرافیت انبساط‌‌یافته و نانولوله کربن به ترتیب 23.2، 27.3 و %24.7 به‌دست آمد. سپس، نمونه‌های مزبور زیر بار خمش قرار گرفته و به ازای 0.5، 1، 1.5، 2 و 2.5mm جابه‌جایی عرضی، مقدار رسانندگی الکتریکی حین بارگذاری و پس از باربرداری اندازه‌گیری شد.
یافته‌ها: نتایج این پژوهش نشان داد، مقدار کاهش رسانندگی الکتریکی در نمونه‌های کربن-اپوکسی دارای نانو‌لوله‌‌های کربنی ناشی از خمش کمترین مقدار و در نمونه‌های کربن-اپوکسی دارای دوده بیشترین مقدار بود. در ادامه، نمونه‌ها مطابق استاندارد خمش سه‌نقطه‌ای زیر بار خمشی قرار گرفتند و مقدار استحکام خمشی نمونه‌ها به‌دست آمد. با استفاده از تصاویر میکروسکوپ الکترونی پویشی کیفیت توزیع نانوذرات در نمونه‌ها مطالعه شد. یافته‌های این پژوهش می‌تواند در ساخت الکترودهای کامپوزیتی رسانایی استفاده شود که زیر بار خمشی (مخازن الکتروستاتیک نمک‌زدایی نفت خام) قرار می‌گیرند.

کلیدواژه‌ها


عنوان مقاله [English]

Effect of Bending Load on the Electrical Conductivity of Carbon/Epoxy Composites Filled with Nanoparticles

نویسندگان [English]

  • Morteza Razavi 1
  • Mohammad Tabatabaee Ghomi 2
  • Fatollah Taheri-Behrooz 3
  • Golamhossein Liaghat4 4
1 Technology Development Institute, ACECR, P.O. Box 13445-686, Tehran, Iran
2 Department of Mechanical Engineering, University of Science and Culture, P.O. Box: 14619-68151, Tehran, Iran
3 School of Mechanical Engineering, Iran University of Science and Technology, P.O. Box 16846-13114, Tehran, Iran
4 Department of Mechanical Engineering, Tarbiat Modares University, P.O. Box 14115-146, Tehran, Iran
چکیده [English]

Hypothesis: The purpose of this study was to investigate the effect of bending load on the electrical conductivity of carbon-epoxy composites containing various nanoparticles. The developed samples, while having sufficient flexural strength, must have the electrical conductivity proposed by the U.S Energy Institute to be used in the manufacturing of electrodes.
Methods: For this purpose, carbon black nanoparticles, carbon nanotubes and expanded graphite with unidirectional carbon fabrics and epoxy resin were used to make the samples. Carbon black particles, carbon nanotube and expanded graphite with optimum weight percentages (25, 10 and 15%) were added to carbon/epoxy composite and the electrical conductivity threshold of the samples was measured according to the four-point strength method. The average electrical conductivity permeability threshold for composites containing carbon black, expanded graphite and carbon nanotubes was 23.2, 27.3 and 24.7%, respectively. The samples were then subjected to bending load and for the 0.5, 1, 1.5, 2 and 2.5 mm transverse displacement, the electrical conductivity value was measured during loading and unloading.
Findings: The results showed that the value of electrical conductivity loss in carbon/epoxy samples containing carbon nanotubes caused by bending was at lowest and in the carbon/ epoxy containing carbon black samples displayed the highest value. Then, the flexural strength of the specimens was measured using a three-point bending test method. The pattern of nanoparticle distribution in the samples was studied on images acquired by scanning electron microscope images. The result of this research could be used in manufacturing of composite electrodes which are subjected to flexural loading (electrostatic desalting crude oil tanks) in services.

کلیدواژه‌ها [English]

  • carbon black particles
  • expanded graphite particles
  • carbon nanotube particles
  • electrical conductivity threshold
  • bending load
  1. Behaviors of Resol (E) and Novolac Type Phenolic Resin Based Composite Bipolar Plate for Proton Exchange Membrane (PEM) Fuel Cell, Electrochimica Acta, 52, 7330-7336, 2007.
  2. Du L. and Jana S.C., Highly Conductive Epoxy/Graphite Composites for Bipolar Plates in Proton Exchange Membrane Fuel Cells, J. Power Sources, 172, 734-741, 2007.
  3. Bidi A., Liaghat Gh., and Rahimi Gh., Effect of Nano Clay Addition to Energy Absorption Capacity of Steel-polyurea Bi-layer, J. Sci. Technol. Compos., 3, 157-164, 2016.
  4. Johnson B.A., Thermally and Electrically Conductive Polypropylene Based Resins for Fuel Cell Bipolar Plates, Thesis, Michigan Technological University, 2009.
  5. Mighri F., Huneault M.A., and  Champagne M.F., Electrically Conductive Thermoplastic Blends for Injection and Compression Molding of Bipolar Plates in the Fuel Cell Application, Polym. Eng. Sci., 44, 1755-1765, 2004.
  6. Gholami H., Shakeri A., and Moosavi S.H., Preparation and Properties Investigation of Conductive Polyaniline-Zinc Oxide Nanocomposites, J. Sci. Technol. Compos., 2, 7-12, 2015.
  7. Chen S., Bourell D. L., and Wood K.L., Fabrication of PEM Fuel Cell Bipolar Plates by Indirect Selective Laser Sintering (SLS), Proceeding of Solid Freeform Fabrication Symposium,244-256, 2004.
  8. Wang Y., Conductive Thermoplastic Composite Blends for Flow Field Plates for Use in Polymer Electrolyte Membrane Fuel Cells (PEMFC), Thesis, University of Waterloo, 2006.
  9. Kakati B., Sathiyamoorthy D., and  Verma A., Electrochemical and Mechanical Behavior of Carbon Composite Bipolar Plate for Fuel Cell, Int. J. Hydrogen Energ., 35, 4185-4194, 2010.
  10. Shen C.h., Mu P., and  Yuan R.z., Sodium Silicate/Graphite Conductive Composite Bipolar Plates for Proton Exchange Membrane Fuel Cells, J. Power Sources, 162, 460-463, 2006.
  11. Jin J., Lin Y., Song M., Gui C., and  Leesirisan S., Enhancing the Electrical Conductivity of Polymer Composites, Eur. Polym. J., 49, 1066-1072, 2013.
  12. Dweiri R. and Sahari J., Computer Simulation of Electrical Conductivity of Graphite-Based Polypropylene Composites Based on Digital Image Analysis, J. Mater. Sci., 42, 10098-10102, 2007.
  13. Rhodes S.M., Higgins B., Xu Y., and  Brittain W.J., Hyperbranched Polyol/Carbon Nanofiber Composites, Polym. J., 48, 1500-1509, 2007.
  14. Barton R., Keith J., and  King J., Development and Modeling of Electrically Conductive Carbon Filled Liquid Crystal Polymer Composites for Fuel Cell Bipolar Plate Applications, J. New Mater. Electrochem., 10, 225, 2007.
  15. Hsiao M.C., Electrical and Thermal Conductivities of Novel Metal Mesh Hybrid Polymer Composite Bipolar Plates for Proton Exchange Membrane Fuel Cells, J. Power Sources, 195, 509-515,2010.
  16. Liao S.H., Hsiao M.C., Yen C.Y., Ma C.C. M., Lee S.J., Su A., Tsai M.C., Yen M.Y., and Liu P.L., Novel Functionalized Carbon Nanotubes as Cross-Links Reinforced Vinyl Ester/Nanocomposite Bipolar Plates for Polymer Electrolyte Membrane Fuel Cells, J. Power Sources, 195, 7808-7817, 2010.
  17. Liao S.H., Hung C.H., Ma C.C. M., Yen C.Y., Lin Y.F., and Weng C.C., Preparation and Properties of Carbon Nanotube-Reinforced Vinyl Ester/Nanocomposite Bipolar Plates for Polymer Electrolyte Membrane Fuel Cells, J. Power Sources, 176, 175-182, 2008.
  18. Du L. and Jana S.C, Hygrothermal Effects on Properties of Highly Conductive Epoxy/Graphite Composites for Applications as Bipolar Plates, J. Power Sources, 182, 223-229, 2008.
  19. Sun L., Cui R., Jalbout A., Li M., Pan X., Wang R., and  Xie H., LiFePO4 as an Optimum Power Cell Material, J. Power Sources, 189, 522-526, 2009.
  20. Park S.M., Jung D.H., Kim S.K., Lim S., Peck D., and  Hong W.H.,The Effect of Vapor-Grown Carbon Fiber as an Additive to the Catalyst Layer on the Performance of a Direct Methanol Fuel Cell, Electrochimica Acta, 54, 3066-3072, 2009.
  21. Shokrieh M.M., Esmkhani M., Vahedi F., and  Shahverdi H.R., Improvement of Mechanical and Electrical Properties of Epoxy Resin with Carbon Nanofibers, Iran. Polym. J., 22, 721-727, 2013.
  22. Bourell D., Leu M.C., Chakravarthy K., Guo N., and Alayavalli K., Graphite-Based Indirect Laser Sintered Fuel Cell Bipolar Plates Containing Carbon Fiber Additions, CIRP Annals-Manufact. Technol., 60, 275-278, 2011.
  23. Guo N. and  Leu M.C., Effect of Different Graphite Materials on the Electrical Conductivity and Flexural Strength of Bipolar Plates Fabricated Using Selective Laser Sintering, J. Hydrogen Energ., 37, 3558-3566, 2012.
  24. Hosseini  M. and Zandi Baghche Maryam A., Electromechanical Response Analysis of a Rotating Piezoelectric Cylinder with Functionally Graded Material Under Thermomagnetic Fields, J. Sci. Technol. Compos., 3, 59-72, 2016.
  25. Taherian R., Hadianfard M.J., and  Golikand A.N., Manufacture of a Polymer-Based Carbon Nanocomposite as Bipolar Plate of Proton Exchange Membrane Fuel Cells, Mater. Desing, 49, 242-251, 2013.
  26. Taherian R., Golikand A.N., and  Hadianfard M.J., The Effect of Mold Pressing Pressure and Composition on Properties of Nanocomposite Bipolar Plate for Proton Exchange Membrane Fuel Cell, Mater. Desing, 32, 3883-3892, 2011.
  27. Taherian R., A Review of Composite and Metallic Bipolar Plates in Proton Exchange Membrane Fuel Cell: Materials, Fabrication, and Material Selection, J. Power Sources, 265, 370-390, 2014.
  28. Modarresi-Alam A.R., Soleimani M., Pakseresht M., Farzaneh-Jobaneh E., Zeraatkar V., Tabatabaei F.A., Shabzendedar S., and  Movahedifar F., Preparation of New Conductive Nanocomposites of Polyaniline and Silica under Solid-State Condition, Polym. Int., 29, 387-398, 2016.
  29. Tabatabaee M., Taheri-Behrooz F., Razavi M., and Liaghat G., Electrical Conductivity Enhancement of Carbon/Epoxy Composites Using Nanoparticles, J. Sci. Technol. Compos., 5, 605-614, 2019.
  30. Li Zhang., Hua Deng., and Qiang Fu., Recent progress on Thermal Conductive and Electrical Insulating Polymer Composite, Compos. Commun., 8, 74-82, 2018.
  31. Chen Y.F., Li J., and Tan Y.J., Low Magnetic Field-Induced Morphological Regulation in Isotactic Polypropylene/Poly(ε-caprolactone)/Carbon Black Composites for High Electrical Conductivity and Conductive Anisotrop, Compos. Commun., 9, 58-62, 2018.
  32. Akhlaghi R., Bahramian A.R., and  Kashani M.R., The Effect of Graphite Nanoparticles on Thermal Stability and Ablation of Phenolic/Carbon Fiber/Graphite Nanocomposites, Iran. J. Polym. Sci. Technol., 27, 241-249, 2014.
  33. Karimi M., Ghajar R., and Montazeri A., Investigation of Nanotubes’Length and Their Agglomeration Effects on the Elastoplastic Behavior of Polymer-Based Nanocomposites, J. Sci. Technol. Compos. (Persian), 4, 229-240, 2017.
  34. TORAYCA®|TORAY, http://www.torayca.com/en/, Available 4 September 2018.
  35. Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials, Annual Book of ASTM Standard, D7264, 2007.
  36. Wafers S., Sheet Resistance of Thin Metallic Films with a Collinear Four-Probe Array 1. Measurement, 98, 1-4 , 2003.
  37. Pan Y.X., Yu Z.Z., Ou Y.C., and Hu G.H., New Process of fabricating Electrically Conducting Nylon 6/Graphite Nanocomposites via Intercalation Polymerization, J. Polym. Sci. Polym. Phys., 1628-1633, 2000.
  38. Standard Test Methods for Constituent Content of Composite Materials, Annual Book of ASTM Standard, D3171, 2010.
  39. Shokrieh M.M. and  Esmkhani M., Experimental Investigation on Fatigue Behavior of Epoxy Resin under Load and Displacement Controls, Iran. J. Polym. Sci. Technol. (Persian), 27, 382, 2014.
  40. Shokrieh M.M. and  Safarabadi M., Influence of Physical, Thermal and Mechanical Parameters on Micro Residual Stresses in Polymeric Composites, Iran. J. Polym. Sci. Technol. (Persian), 24, 355-368, 2012.
  41. Hosseini H., Kokabi M., and  Ebrahimi N.G., Vertical Electrospinning of Uhmwpe/ZnO Nanocomposite Fibers at High Temperature, Iran. J. Polym. Sci. Technol. (Persian), 27, 131-141, 2014.
  42. Mokarrar Industrial Group, http://mokarrar.com/en, Available 4 September 2018.
  43. Shimimarket, http://www.shimimarket.com, Available 4 September 2018.
  44. AMG Graphite-Graphit Kropfmühl GmbH, Available at https://www.gk-graphite. com/home, Accessed 4 September 2018.