Effective Parameters on Reaction Kinetics and Particle Size in the Suspension Polymerization of Styrene in the Presence of Graphite

Document Type : Research Paper

Authors

1 Institute of Polymeric Materials, Sahand University of Technology, Postal Code 5331817634, Tabriz, Iran

2 Research and Development Center, Tabriz Petrochemical Complex , Postal Code 5197133377, Tabriz, Iran

Abstract

Hypothesis: suspension polymerization of styrene in the presence of graphite was carried out. The polymerization reaction kinetics was investigated to gain better insight into manipulating process parameters. The particle size distribution and thermal conductivity of the foams were studied by considering different parameters.
Methods: Product characterization and the reaction thermal kinetics were evaluated using differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), particle size distribution and thermal conductivity measurements. The effect of graphite and initiator concentration on the reaction kinetics was investigated.
Findings: The results showed that the graphite profoundly reduced the rate of reaction and consequently caused instability in the suspension. By manipulating the process variables such as increasing the amount of stabilizers (1 to 2%) and initiator (up to 0.6% by wt), their frequency and injection time, the polymerization of styrene in the presence of graphite was done. The beads were spherical and the superfine (less than 420 μm) proportion of the product was less than 5%. Through the pre-expansion process, the beads were expanded and the cell structure was uniform. The pentane content of the beads was sufficient (~7% by wt) to successfully sinter the pre-expanded beads in the final molding process. Final foams had 0, 1 and 1.5% graphite. By increasing the graphite content, the thermal conductivity of the foams was decreased. Graphite-containing foams were better thermal insulators than conventional expandable polystyrene. Therefore, for a specific thermal duty, a smaller amount of graphite-containing expandable polystyrene rather than conventional polystyrene is required and consequently, the total cost of the insulation is reduced.

Keywords

References

  1. Yuan B., Wang G., Bai S., and Liu P., Preparation of Halogen-Free Flame-Retardant Expandable Polystyrene Foam by Suspension Polymerization, J. Appl. Polym. Sci., 136, 47779, 2019.
  2. Maggioris D., Goulas A., Alexopoulos A.H., Chatzi E.G., and Kiparissides C., Prediction of Particle Size Distribution in Suspension Polymerization Reactors: Effect of Turbulence Nonhomogeneity, Chem. Eng. Sci., 55,4611-4627, 2000.
  3. Alvarez J. and Hernandez M., A Population Balance Approach for the Description of Particle Size Distribution in Suspension Polymerization Reactors, Chem. Eng. Sci., 49, 99-113, 1994.
  4. Chaudhary V. and Sharma S., Suspension Polymerization Technique: Parameters Affecting Polymer Properties and Application in Oxidation Reactions, J. Polym. Res., 26, 102, 2019.
  5. Georgiadou S. and Brooks B. W., Suspension Polymerisation of Methyl Methacrylate Using Sodium Polymethacrylate as a Suspending Agent, Chem. Eng. Sci., 60,7137-7152, 2005.
  6. Li B.Y., Wang Y.P., Niu X.B., and Liu Z.M., Suspension Polymerization of Methyl Methacrylate Stabilized Solely by Palygorskite Nano Fibers, Chinese J. Polym. Sci., 32,123-129, 2014.
  7. Dowding P.J. and Vincent B., Suspension Polymerisation to Form Polymer Beads, Colloid. Surf., A: physicochem. Eng. Asp., 161,259-269, 2000.
  8. Saeidi M., Mohebali S., Shamskar K.R., and Sayyadnejad M.A., To Control Bead Size Distribution in Suspension Polymerization, Iran J. Polym. Sci. Technol. (Persian), 21,409-415, 2008.
  9. Daneshgar M., Farahani E.V., and Haghighi M.N., The Effects of Temperature, Initiator and Stabilizer on Polymer Particle Size in Suspension Polymerization of Styrene, Iran J. Polym. Sci. Technol. (Persian), 23,499-507, 2011.
  10. Jozaghkar M.R., Ziaee F., Aqda M. R.A., Yaghobi N., and Jalilian S.M., Effect of Different Polar Solvents and Stabilizer and Co-stabilizer Concentration on Dispersion Polymerization of Styrene, Iran J. Polym. Sci. Technol. (Persian), 32,171-181, 2019.
  11. Jalili K., Abbasi F., Nasiri M., Ghasemi M., and Haddadi E., Preparation and Characterization of Expandable St/MMA Copolymers Produced by Suspension Polymerization, J. Cell. Plast., 45,197-224, 2009.
  12. Jalili K., Abbasi F., and Nasiri M., Copolymerization of Styrene and Methyl Methacrylate. Part I: Experimental Kinetics and Mathematical Modeling, Polymer, 52,4362-4376, 2011.
  13. Barkanyi T., Nemeth S., and Lakatos B.G., Modelling and Simulation of Suspension Polymerization of Vinyl Chloride via Population Balance Model, Comput. Chem. Eng., 59,211-218, 2013.
  14. Castor C.A., Jr., Pontier A., Durand J., Pinto J.C., and Prat L., Real Time Monitoring of the Quiescent Suspension Polymerization of Vinyl Chloride in Microreactors-Part 2. A Kinetic Study by Raman Spectroscopy and Evolution of Droplet Size, Chem. Eng. Sci., 145,279-293, 2016.
  15. Abedin R., Pojman J.A., Knopf F.C., and Rice R.G., Suspended Droplet Polymerization in an Unstable, Vibrating Shallow-Bed Reactor, Ind. Eng. Chem. Res., 55,2493-2503, 2016.
  16. Ziaee F., Basiri M., Nekoomanesh M., and Khazaie A., Kinetic Investigation of Styrene Free Radical Polymerization by Using Binary Mixtures of Monofunctional Initiators, Iran J. Polym. Sci. Technol. (Persian), 22,133-140, 2009.
  17. Shaghaghi S., Bulk Polymerization of Styrene with Two Initiators, Iran J. Polym. Sci. Technol. (Persian), 14,121-127, 2001.
  18. Bozorg M., Abdollahi M., and Semsarzadeh M. A., Effects of Molecular Iodine and 4-tert-Butylcatechol Radical Inhibitor on the Radical Polymerization of Styrene, Iran J. Polym. Sci. Technol. (Persian), 30,95-104, 2017.
  19. Nikakhtar A., Jahanzad F., and Haghighi M.N., Mathematical Model for Determination of Kinetics Behaviour of Styrene Polymerization, Iran J. Polym. Sci. Technol. (Persian), 12,91-99, 1999.
  20. Shao X., Du Y., Zheng X., Wang J., Wang Y., Zhao S., Xin Z., and Li L., Reduced Fire Hazards of Expandable Polystyrene Building Materials via Intumescent Flame-Retardant Coatings, J. Mater. Sci., 55,7555-7572, 2020.
  21. Chung D.D.L., Review: Graphite, J. Mater. Sci., 37,1475-1489, 2002.
  22. Huang J., Zhao Z., Chen T., Zhu Y., Lv Z., Gong X., Niu Y., and Ma B., Preparation of Highly Dispersed Expandable Graphite/Polystyrene Composite Foam via Suspension Polymerization Non-Covalently Compatibilized by Polystyrene with Enhanced Fire Retardation, Preparation of Highly Dispersed Expandable Graphite/Polystyrene Composite Foam via Suspension Polymerization Non-Covalently Compatibilized by Polystyrene with Enhanced Fire Retardation, 146,503-512, 2019.
  23. Ji W., Yao Y., Guo J., Fei B., Gu X., Li H., Sun J., and Zhang S., Toward an Understanding of How Red Phosphorus and Expandable Graphite Enhance the Fire Resistance of Expandable Polystyrene Foams, J. Appl. Polym. Sci., 137, 49045, 2020.
  24. Zhang C., Li X., Chen S., and Yang R., Effects of Graphite on Styrene Suspension Polymerization and Flame Retarded Expandable Polystyrene, Polym. Mater. Sci. Eng., 32,6-11, 2016.
  25. Ferreira G.R., Segura T., de Souza Jr F.G., Umpierre A.P., and Machado F., Synthesis of Poly(vinyl acetate)-Based Magnetic Polymer Microparticles, Eur. Polym. J., 48,2050-2069, 2012.
  26. Zheng Z., Li W., Sun H., Cheng Z., Yan J., Wang H., and Cui X., Preparation and Characterization of Polystyrene/Modified Carbon Black Composite Beads via in Situ Suspension Polymerization, Polym. Compos., 34,1110-1118, 2013.
  27. Hwu J.M., Ko T.H., Yang W.T., Lin J.C., Jiang G.J., Xie W., and Pan W.P., Synthesis and Properties of Polystyrene-Montmorillonite Nanocomposites by Suspension Polymerization, J. Appl. Polym. Sci., 91,101-109, 2004.
  28. Odian G., Principles of Polymerization, 4th ed. Hoboken, New Jersey, John Wiley and Sons, Inc., 2004.
  29. Mihlayanlar E., Dilmac S., and Guner A., Analysis of the Effect of Production Process Parameters and Density of Expanded Polystyrene Insulation Boards on Mechanical Properties and Thermal Conductivity, Mater. Des., 29, 344–352, 2008.

 

Iranian Journal of Polymer Science and Technology
Volume 33, Issue 2 - Serial Number 166
July and August 2020
Pages 137-146

Files

Share

How to cite

Statistics