اثر مقدار و توزیع وزن مولکولی و ریزساختار لاستیک استیرن- بوتادی‌ان محلولی بر خواص مکانیکی و دینامیکی آمیزه‌های لاستیکی دوده‌ای با سامانه‌‌های گوناگون پخت گوگردی

نوع مقاله : پژوهشی

نویسندگان

تهران، پژوهشگاه پلیمر و پتروشیمی ایران، پژوهشکده فرایند پلیمرها, گروه لاستیک، صندوق پیستی 112-14975

چکیده

فرضیه: خواص فیزیکی و مکانیکی آمیزه‌های لاستیکی تهیه‌شده از کائوچوی استیرن-بوتادی‌اِن محلولی (SSBR) تابعی از پارامترهای ساختاری (وزن مولکولی و توزیع آن، درصد شاخه جانبی وینیلی و استیرن) و سامانه پخت انتخابیاست که در این پژوهش به بررسی دوسویه آن‌ها پرداخته خواهد شد.
روش‌ها: در این پژوهش سه گونه تجاری کائوچوی SSBR انتخاب شدند. وزن مولکولی و توزیع آن‌ها با دستگاه GPC‌ اندازه‌گیری شد. چهار سامانه پخت دو شتاب‌دهنده‌ای در نظر گرفته و درمجموع 12 آمیزه ساخته و پس‌ از آن نمونه‌های مربوط تهیه شدند. آزمون‌های موردنیاز روی نمونه‌ها انجام شد که شامل اندازه‌گیری مدول ذخیره و اتلاف آمیزه‌های پایه، خواص پخت، خواص مکانیکی ایستا (مقاومت کششی، درصد ازدیاد طول تا پارگی، مدول و سختی) ، مقاومت سایشی ، خواص دینامیکی با DMTA‌ (روبش گرمایی در کرنش و بسامد ثابت) و RPA‌ (روبش کرنش در دما و بسامد ثابت) بودند.
یافته‌ها: نتایج نشان داد، افزایش وزن مولکولی موجب کاهش اثر پیِن در آمیزه‌های پایه و پخت شده می‌شود. آمیزه‌های دارای شتاب‌دهنده TMTD‌ چگالی اتصال‌های عرضی و سختی بالاتری داشته که باافزایش وزن مولکولی تشدید می‌شود. اما در مقابل سایش بیشتری از خود نشان می‌دهند. کاهش دمای گذار شیشه‌ای و در صد شاخه جانبی وینیلی نیز  بهذ بهبود مقاومت سایشی منجر می‌شود. مقایسه بین دو کائوچو با ریزساختارهای تقریباً یکسان نشان داد، کائوچوی با توزیع وزن مولکولی پهن‌تر به‌نحوی‌که شامل زنجیرهایی با طول بیشتر باشد، خواص بهتری دارد. همچنین آمیزه‌های ساخته‌شده با کائوچوی با وزن مولکولی بیشتر و توزیع متوسط و نیز شاخه جانبی وینیلی کمتر دارای کمترین و بیشترین ضریب اتلاف به‌ترتیب در محدود دمایی 60 و صفر درجه سلسیوس بوده و نیز دمای گذار شیشه‌ای کمتری بوده که می‌تواند به‌عنوان کائوچوی مناسب برای کاربرد در رویه تایر استفاده شود.

کلیدواژه‌ها

موضوعات


عنوان مقاله [English]

Study on the Variations of Molecular Weight and Its Distribution and Micro-structure on Mechanical and Dynamical Properties of CB Reinforced SSBR Compounds Using Different Curing Systems

نویسندگان [English]

  • Mir Hamid Reza Ghoreishy
  • Foroud Abbassi Sourki
  • Mohammad Mahdi Vahedi
Department of Rubber Processing and Engineering, Faculty of Processing, Iran Polymer and Petrochemical Institute, P.O. Box: 14975-112, Tehran, Iran
چکیده [English]

Hypothesis: The physical and mechanical as well as the viscoelastic properties of SSBR compounds are strongly dependent on the molecular weight and its distribution, 1,2 vinyl branch, and styrene content, as well as the selected cure system which has been thoroughly studied in this work 
Methods: Three commercial SSBR grades were selected. The GPC technique was used to determine the molecular weight and its distributions. Four conventional sulfur cure systems with two primary and secondary accelerators were chosen and 12 compounds have been prepared with their corresponding test specimens. A series of experiments were conducted including the measurements of the storage and loss moduli of the master compounds, cure properties, mechanical properties (tensile strength, elongation-at-break, modulus and hardness), abrasion resistance, dynamic mechanical thermal analysis (temperature sweep at a constant frequency) and dynamic properties using RPA (strain sweep at constant frequency and temperature)
Findings: Increasing the molecular weight would decrease the Payne effect in master compounds. Rubber compounds with TMTD as the secondary accelerator have higher crosslink density and hardness which have been enhanced with increasing the molecular weight but the abrasion resistance was decreased. A comparison of the mechanical properties between compounds prepared with an identical micro-structure revealed that rubber with a broader molecular weight distribution and longer chains shows better mechanical properties. In addition, the compounds in which the rubber has a higher molecular weight, average polydispersity index, lower glass transition temperature, and lower 1,2 vinyl content showed lower and higher loss factors at 60 oC and 0 oC, respectively. This indicates that it can be used as a good potential rubber in tire tread.

کلیدواژه‌ها [English]

  • Tire
  • SSBR
  • Cure system
  • Dynamic properties
  • Molecular weight distribution